---
title: "HP Quanta LB6M交换机常用配置命令"
id: "104"
type: "post"
slug: "hp-quanta-lb6m%e4%ba%a4%e6%8d%a2%e6%9c%ba%e5%b8%b8%e7%94%a8%e9%85%8d%e7%bd%ae%e5%91%bd%e4%bb%a4"
published_at: "2018-01-21T09:02:34+00:00"
modified_at: "2018-09-12T11:57:10+00:00"
url: "https://www.hitsword.org/2018/104.html"
markdown_url: "https://www.hitsword.org/2018/104.md"
excerpt: "Console连接 可以使用Cisco Console线 波特率：9600 数据位：8 停止位：1 流量控制： […]"
taxonomy_category:
  - "交换机"
taxonomy_post_tag:
  - "Cisco"
  - "LB6M"
  - "交换机"
---

# HP Quanta LB6M交换机常用配置命令

- Console连接 **可以使用Cisco Console线 波特率：9600 数据位：8 停止位：1 流量控制：无 默认账号:admin 默认密码:空 进入enable模式:enable 默认enable密码:空**
- 刷机/备份固件 **连接LB6M后进入enable模式** ``` show bootvar //显示当前固件 copy tftp://IP/xxx.img backup//从tftp上传固件到backup boot system backup //下次启动使用backup固件启动 reload //重启 copy active tftp://IP/active.img//下载active固件到tftp copy backup active//把backup固件复制到active固件 ``` 还可以copy以下内容 ``` nvram:backup-config backup Config file. nvram:clibanner CLI Banner file. nvram:errorlog Errorlog file. nvram:fastpath.cfg Binary Config file. nvram:log Log file. nvram:script Configuration Script file. nvram:startup-config startup Config file. nvram:traplog Trap log file. system:running-config running system config file. ```
- Console 恢复出厂 **连接Console后插上电源。 显示“FASTPATH Startup — Main Menu”时选2显示菜单 选6清空配置 选13重启**
- 配置网管端口 **连接LB6M后进入enable模式** 显示网管口状态:**show serviceport** ``` Interface Status............................... Up IP Address..................................... 192.168.0.150 Subnet Mask.................................... 255.255.255.0 Default Gateway................................ 192.168.0.1 Configured IPv4 Protocol....................... DHCP Burned In MAC Address.......................... XX:XX:XX:XX:XX:F3 ``` 禁用DHCP(默认是DHCP)**serviceport protocol none** 设置静态IP:**serviceport ip 192.168.1.100 255.255.255.0 192.168.1.1 格式：serviceport ip IP MASK Gateway**
- 配置网络端口 **连接LB6M后进入enable模式** 显示网络口状态:**show network** ``` Interface Status............................... Up IP Address..................................... 192.168.0.151 Subnet Mask.................................... 255.255.255.0 Default Gateway................................ 192.168.0.1 Burned In MAC Address.......................... XX:XX:XX:XX:XX:F2 Locally Administered MAC address............... 00:00:00:00:00:00 MAC Address Type............................... Burned In Configured IPv4 Protocol....................... DHCP Management VLAN ID............................. 1 ``` 禁用DHCP(默认是DHCP)**network protocol none** 设置静态IP:**network parms 192.168.0.100 255.255.255.0 192.168.0.1 格式：network parms IP MASK Gateway**
- 配置SSH并关闭telnet **连接LB6M后进入enable模式** ``` ip ssh protocol 2 //ssh版本2 ip ssh server enable //启用ssh ip telnet server disable//关闭telnet ```
- 设置密码与enable密码 **连接LB6M** ``` password 密码//设置密码 enable//进入enable模式 enable password 密码//设置enable密码 ```
- 配置NTP与时区 **连接LB6M后进入enable模式** ``` configure//进入配置模式 sntp client mode unicast //ntp模式 sntp client port 123 //ntp端口 sntp server pool.ntp.org //ntp服务器 clock timezone 8 minutes 0 //系统时区 exit//退出配置模式 show clock //显示当前时间 ```
- 其他 ``` hostname xxxsw//设置HOSTNAME show running-config//显示当前配置 clear config//清空设置 write memory//保存 reload//重启 ```